QR Code Link to This Post
U.S. Made with a 2 Year Gearbox Guaranty. These shredders, brush hogs are designed for 15 HP - 40 HP range tractors. They include a 40 HP Gear Box, Stump Jumper, No-Flat Tire & Wheel Assembly with Slip Clutch (SC) for Drive-line protection. Also are Powder Coated paint for long-lasting life and our Agri-X cutters are higher rated than the TSC County Line brand which retails for a lot more without powder-coated paint or stump-jumper.
Brush Hogs/Rotary Cutters Standard Duty:
48" Agri TTX4 SB 4’ Brush Hog with Shear Bolt: $1,311.00
48" Agri TTX4 SC 4’ Brush Hog with Slip Clutch: $1,441.00
60" Agri TTX5 SB 5’ Brush Hog with Shear Bolt: $1,441.00
60" Agri TTX5 SC 5’ Brush Hog with Slip Clutch: $1,555.00
72" Agri TTX6 SB 6’ Brush Hog with Shear Bolt: $1,641.00
72" Agri TTX6 SC 6’ Brush Hog with Slip Clutch: $1,757.00
*Add a 85 HP Gear Box to the 5' or 6' model for $300 more. AND see our HD 6' model the TTMD685 mentioned below.
The following features are included on the 4, 5 AND 6' Cutters which create a dependable machine that can withstand years and years of use:
• Sturdy one-piece heavy 12-gauge steel frame.
• Reinforced weldments are added at stress points.
• The blade carrier is formed from a one-piece 12-gauge steel plate.
• The blade carrier has a 5/8" bar welded for extra strength and durability. Sides plates are a deep 7" depth.
• Cutting height with tail wheel on ground is adjustable from 2 to 7". Can cut higher using your 3-Point draft control with the tail wheel off the ground.
• The blade carrier rides over stumps and rocks, reducing gearbox and driveline failure. The disc also serves as a flywheel giving you more cutting power.
• The A-frame style 3-point hitch is a one-piece hitch and attaches to the mainframe allowing a fold back or flex action.
• The adjustable tail wheel gives you a variety of cutting heights.
• The 40 HP gearbox has a flange mount that is bolted to a welded, one-piece reinforcement plate on the rotary cutter mainframe.
• The PTO shaft has needle bearings in the cross joint and grade 2 shear pins.
• The blades and blade bolts are heat treated and matched to give you a swing action. The design of the blades creates an upward suction when in centrifugal motion contributing to a lower, cleaner cut."
* Note: all models are tapered and with powder coated. Powder coating can maintain its finish for 10 to 20 years or more depending on care.
Also available HEAVY DUTY in 6' and 7' sizes. See PHOTO above for more specs on our top of the line MD Cutters with: Dual Tail Wheels, 10 Gauge Deck, Fast Quick Hitch Compatible and 85 HP Gear Box.
*The TTMD685 is our HD 6' Model (945 lbs.) is $2,654.
*The TTMD785 is our HD 7' Model (980 lbs.) is $3,177.
(Chains front, back add $248 on the 6’ and $295 on the 7’ models)
The following 3 ATLAS Models all have slip clutch, safety chains front and rear, 2 tail wheels and like the rest have Powder Coat paint. In addition, these models all have 12-Gauge HD decks and are two-spindle with 3 Gear Boxes:
DELIVERY NOTE: If you purchase an 8' or 10' Foot cutter and have it they are shipped in the upright position as shown. The buyer is responsible for the following: 1) unloading cutter from the delivery trailer upon arrival and 2) due to size these cutters are shipped in the upright position so the buyer is required to do a basic set up of the hitch frame and grease all pins before use (estimate 30 minutes).
PICKUP NOTE: If you purchase an 8’ or 10’ cutter and pick it up locally we can load it out the same as described above. If you are going to pull the cutter home via truck or tractor we can do the basic setup for you at no charge, however be aware the cutters are oversized for travel on the road. It is the buyers responsibility to attain any permits if required for road travel.
96” 8’ HD TTSCL96 Model with (3) 85 HP Gear Boxes, etc. $4,876.
TT 10’ 3-Point Hitch model, (3) 85 HP Gear Boxes, etc. $5,879.
TT 10’ Pull Behind / Drag model TTSCD120, (3) 85 HP Gear Boxes, etc. $6,445.
*Add for Hydraulic Hose & Cylinder Kit $296.
Minimum PTO HP Recommendations: 4'=18 PTO HP. 5'=24 PTO HP. 6'=30-32 PTO HP (Our HD TTMD685 Model at 36-40 PTO HP). 7'=45-50 PTO on our HD TTMD785 Model. 8'=50 PTO HP. 10' Lift 3-Point Model=60 PTO HP. 10' Drag Pull Model=50 PTO HP (45 Min. PTO HP in medium and pasture type conditions).
SHIPPING: Can palletize and ship in the U.S. for $200 to $550 range depending on how far you are away from TN. Shipment to the far northeast U.S. or the west coast slightly more. Or feel free to arrange your own freight pick up and we can load this item onto any type trailer into any enclosed truck or trailer.
For more information, call the Sales Department at 931**422**2300 - Extension 1 (7:30am-5pm M-F. Sat. till noon CST).
